It does not require special
professional training.
professional training.
Selective rf detector raksa iDet
6 modes of operation: security, review, search, search with subtraction, monitoring, audio monitoring, as well as a log of alarm events.
User-friendly and functional interface.
User-friendly and functional interface.
Monitoring ModeMonitoring Mode provides continuous monitoring of detected analog and digital radio signals in automatic mode and setting alarm in case of threat radio signal (signal exceeding the preset threshold level) detection. Monitoring Mode is used in cases when the primary signal source has not been activated. The information about the alarm events is recorded in the Alarm Log.
Monitoring Mode enables the background noise deduction for analog signals thus reducing the influence of regular background noise. Slow fluctuations of its level are ignored thanks to the adaptation algorithm.
Sweep ModeSweep Mode is used for detection of analog and digital radio signals of all types. This mode allows the review of all detected signals regardless their level.
Search ModeThe Search Mode is used for detection and location of analog and digital transmitters. This mode is used when you can move the RF Detector around searching for a radio transmitter.
Search Mode for analog signals utilizes both light and sound indication of the signal strength: the higher is the frequency of flash the closer is the transmitter.
Difference Search ModeDifference Search Mode is used for detection and localization ofanalog transmitters. This mode has its advantage in case the transmitter is located in the same room.
In this Mode the device defines the relative level of the signal — its difference with the reference spectrum that was fixed at the beginning of operation in this Mode. The closer to the source of radio signal located in the room the higher is its signal level in comparison with the outside radio transmitter. The RF Detector selectively reacts to the change of level thus enabling to locate the radio transmitter at a higher rate.
Differential Search Mode utilizes both light and sound indication of the relative signal level.
Monitoring of Digital SignalsMonitoring of Digital Signals is intended for detection of mobile phone signals (GSM, UMTS(3G), CDMA types), cordless telephones (DECT standard), Bluetooth, Wi-Fi and other impulse signals in 2.4 GHz.
In Monitoring of Digital Signals the display shows the list of all digital signals and their strength levels.
Audio MonitoringAudio Monitoring is available only for analog signals in Sweep, Search and Difference Search Modes through the built-in speaker. The audio monitoring facilitates signal identification and allows using the acoustic feedback.
Alarm Events LogAlarm Events Log accumulates the information about the threat signals detected in the Monitoring Mode. The max number of records – 200. If the detected threat signals are of different types the Log will record all of them. The display shows the moment of detection and the moment of the signal extinction, the type and the max level of the signal.
Обнаружитель прослушки RAKSA-iDet
25500
руб.
29900
руб.
RF Detektor iDet предназначен для обнаружения в ближней зоне и определения местоположения радиопередающих устройств, использующихся для негласного съема аудио - и видеоинформации и устройств слежения. Работа с индикатором не требует специальной профессиональной подготовки.
RAKSA-iDet - мультиязычная экспортная версия легендарного обнаружителя жучков RAKSA R-121. Дополнительно обнаруживает стандарты связи, которые используются за рубежом, а так же возможность выбрать язык: английский, немецкий, французский, итальянский, испанский и русский. Возможно дополнительно добавить польский и чешский язык.
Инструкция на английском языке.
RAKSA iDet Selective RF Detector can be used to detect and locate in near field a wide variety of digital, analogue and wideband surveillance devices.
RAKSA iDet detects:
Special Features:
RAKSA-iDet - мультиязычная экспортная версия легендарного обнаружителя жучков RAKSA R-121. Дополнительно обнаруживает стандарты связи, которые используются за рубежом, а так же возможность выбрать язык: английский, немецкий, французский, итальянский, испанский и русский. Возможно дополнительно добавить польский и чешский язык.
Инструкция на английском языке.
RAKSA iDet Selective RF Detector can be used to detect and locate in near field a wide variety of digital, analogue and wideband surveillance devices.
RAKSA iDet detects:
- 4G/LTE
- cellular phones of GSM 850/ 900E/1800/1900, UMTS 850/ 900/1800/1900/2100 (3G), CDMA 450 (A-H)/800/1900 standards;
- cordless DECT phones;
- Bluetooth and Wi-Fi devices;
- wireless video cameras;
- radio transmitters with analog modulation (AM, FM, PM);
- radio transmitters with digital modulation and continuous carrier (FSK, PSK, etc.);
- radio transmitters with wideband modulation up to 10 MHz bandwidth.
Special Features:
- signal detection against the background interference
- high speed of scanning and analyzing
- detection of digital, analog and wideband signals
- adaptation to the background noise in Monitoring Mode
- difference search mode
- audio monitoring through the built-in speaker
- signals frequency and level measurement
- alarm events log
- silent alert signal (vibration mode)
- no need for external antenna
- interface languages: Deutsch, English, Espanol, Francais, Italiano, Русский. By pre-order, the following languages are added: Cestina and Polski
Operation Instructions Raksa iDet
Radio transmitter detection requires two complimentary steps – search and guard. Search Mode enables to detect and locate the transmitters activated to the moment. Guard Mode provides continuous monitoring of the radio signals thus the transmitters are detected at the moment of their activation.
Before searching the target area all the radio signal sources should be switched off (mobile and cordless telephones, Bluetooth, Wi-Fi, microwave ovens). To activate the transmitters with voice control use any sound source.
Place the RF detector in the center of the room and switch on Search mode. Gradually approach the probable transmitter locations and watch the possible change of the signal level. Both light and sound indication can be used – the closer to the source of signal – the higher is the frequency of flashes. The high flash increase might indicate a hidden surveillance device.
After verification of the clean area change the mode to Guard and place RF Detector at your convenience. The RF Detector should stay stable to avoid false alarms. The alarm signal is generated when detection a threat radio signal.
The efficiency of radio signal detection in Guard Mode depends on correct setting of threshold levels. The mobile phones for instance are characterized by wide range of signal magnitude. Use the Digital Signals Monitoring Mode to define the signal levels of mobile and cordless phones, Bluetooth and the like and adjust the threshold level if necessary. The higher is the threshold level the less probable is false alarm but distance of detection will lessen as well.
Before searching the target area all the radio signal sources should be switched off (mobile and cordless telephones, Bluetooth, Wi-Fi, microwave ovens). To activate the transmitters with voice control use any sound source.
Place the RF detector in the center of the room and switch on Search mode. Gradually approach the probable transmitter locations and watch the possible change of the signal level. Both light and sound indication can be used – the closer to the source of signal – the higher is the frequency of flashes. The high flash increase might indicate a hidden surveillance device.
After verification of the clean area change the mode to Guard and place RF Detector at your convenience. The RF Detector should stay stable to avoid false alarms. The alarm signal is generated when detection a threat radio signal.
The efficiency of radio signal detection in Guard Mode depends on correct setting of threshold levels. The mobile phones for instance are characterized by wide range of signal magnitude. Use the Digital Signals Monitoring Mode to define the signal levels of mobile and cordless phones, Bluetooth and the like and adjust the threshold level if necessary. The higher is the threshold level the less probable is false alarm but distance of detection will lessen as well.